影響螺桿空壓機實際排氣量的因素

Factors Influencing Actual Exhaust Volume of Screw Air Compressor

1.設備轉速：

1. Equipment speed:

螺桿空壓機的排氣量與轉速成正比，而轉速往往會隨電網的電壓、頻率而變化。當電壓降低或頻率降低時，轉速將下降，使螺桿空壓機排氣量減少。

The exhaust volume of screw air compressor is proportional to the rotational speed, and the rotational speed often varies with the voltage and frequency of power grid. When the voltage or frequency decreases, the speed will decrease, which will reduce the exhaust volume of screw air compressor.

2.吸氣狀態：

2. Inhalation state:

螺桿空壓機是容積型壓縮機，吸氣體積不變。當吸氣溫度升高，或吸氣管路阻力過大而使吸入壓力降低時，氣體的密度減小，相應地會減少螺桿空壓機排氣量；

Screw air compressor is a volumetric compressor with constant gas absorption volume. When the suction temperature increases or the suction pressure decreases due to the excessive resistance of the suction pipeline, the density of the gas decreases and the exhaust volume of the screw air compressor decreases accordingly.

3.氣體泄漏：

3. Gas leakage:

轉子相互之間及轉子與外殼之間在運轉時沒有接觸，保持有一定的縫隙，所以會產生氣體泄漏。壓力升高后的氣體通過縫隙向吸氣管道及正在吸氣的嚙槽泄漏時，將使排氣量減小。為了減少泄漏量，在從動轉子的齒頂做有密封齒，主動轉子的齒根開有密封槽，端面也加工有環狀或條狀的密封齒。如果這些密封線磨損，將使泄漏量增加，因此平時維護的時候應該考慮到這些因素；

There is no contact between the rotors and between the rotors and the outer shell during operation, and there is a certain gap, so gas leakage will occur. When the pressure rises and the gas leaks through the gap to the suction pipe and the suction groove, the exhaust volume will decrease. In order to reduce leakage, sealing teeth are made on the top of the driven rotor teeth, sealing grooves are opened on the root of the active rotor teeth, and ring or strip sealing teeth are machined on the end face. If these sealing wires are worn out, the leakage will increase, so these factors should be taken into account in maintenance.

4.冷卻效果：

4. Cooling effect:

氣體在壓縮過程中溫度會升高，轉子與機殼的溫度也相應升高，所以在吸氣過程中，氣體會受到轉子和機殼的加熱而膨脹，因此相應地會減少吸氣量。螺桿式空氣壓縮機的轉子中有的采用了油冷卻，機殼用水冷卻，其目的之一就是為了降低其溫度。當冷卻效果不好時，溫度則升高，螺桿空壓機排氣量便會減少。

During the compression process, the temperature of the gas will rise, and the temperature of the rotor and the casing will also rise accordingly. Therefore, during the suction process, the gas will expand due to the heating of the rotor and the casing, so the suction capacity will be reduced accordingly. Oil cooling is used in the rotor of screw air compressor and water cooling is used in the casing. One of its purposes is to reduce its temperature. When the cooling effect is not good, the temperature rises and the exhaust volume of screw air compressor decreases.